Fix Need Help Computer Won't Boot Tutorial

Home > Computer Won 39 T > Need Help Computer Won't Boot

Need Help Computer Won't Boot


Other side of the world from the land of the Dodo I'm afraid. Well, what I can say is that it can be that the other motherboard was faulty. Just turn the keys on and off and if the lights go ON and OFF then your system is working. If you don't have another PC to do this then you can always ask for help from a friend or relative.

Try swapping the memory to another slot. Boot into Recovery Mode and click to install Mavericks. Wird verarbeitet... What you said makes a lot of sense.

Computer Won't Boot Windows 10

PinkF ZeppelinJan 10, 2010, 3:13 AM JDFan said: Cardboar is not really good to use as it can carry static charges which are not good for the MOBO - be sure Report Agk- Apr 18, 2009 at 08:53 AM Hi Thanks.. ur solution Helped me tooo.. :) my faulty pci modem was the traitor.. :) Report JohnWayne- Apr 25, 2009 at 07:55 PM I Have a HP Pavillion A1600n that has a

This will allow your computer’s capacitors enough time to totally discharge. But I can't find any fault. Thanks for you assistance. Computer Won't Boot Up Black Screen Realised that my computer does not work I tried the answer's advice to find out which are faulty...

This might occur if you have tried to install another operating system alongside Windows 7, such as Windows XP.  To write a new boot sector, try the following command: bootrec.exe /FixBoot Computer Won't Boot Windows 7 Help answer questions Learn more 223 MalwareTips BlogRemoving malware has never been easier! I went to log off and it died. Viruses, backdoors, keyloggers, spyware ,adware, rootkits, and trojans are just a few examples of what is considered malware.

If it’s an older laptop, it’s worth considering buying a new one. Computer Won't Start computer wont boot windows? Hinzufügen Playlists werden geladen... Normally a faulting PCI modem causes this type of error.

Computer Won't Boot Windows 7

Report An eraser!!!!!! click here now So I turned off and back on and this time it's reverted back to the frozen Motherboard page. Computer Won't Boot Windows 10 I guess it's time to my computer tech. Computer Won't Turn On If nothing else works, you may wish to reset your Mac’s SMC (System Management Controller).

thanks you Report karthik› DJ AKSHAY - Dec 17, 2009 at 12:50 AM Hi DJ Akshay I am a student who is in sydney recently I took an old computer from this content With some basic troubleshooting, you can often solve boot up problems with your Windows or Mac computer. Report navyguy› DJ AKSHAY - Jan 16, 2010 at 11:18 AM ERASER TRICK WORKED FOR ME. If you can see the coloured wires inside the black outer protection, it could be time to buy a new PSU. Laptop Won't Boot

Any help? I'll do that but nothing then once your about to give up on turning on the computer one last try it will eventually turn on but takes a while to boot Also the Two Jumpers to clear out Bios...My board has just pins, no jumpers at all. weblink When I try to shut down my computer it's as if it's going to sleep or simply restarting, never completely shutting down.

Report devonl- Nov 27, 2009 at 04:46 AM Awesome advice DJ Akshay, your advice worked perfectely - you saved me alot of money and frustration ! Computer Not Powering On I took off the cpu cooler and felt the chip for many seconds but it didn't heat up. No beeps or clicks to hint at harddrive failure.

Thanks a ton for helping me, too.

Report DJ AKSHAY 266Posts Sunday December 21, 2008Registration date April 26, 2010 Last seen - Feb 24, 2009 at 11:37 AM If the Charge indicator is ON then the adaptor must The DVD drive still opens, and a few lights blink on start up as usual. Determine which partition you wish to make active. Computer Won't Boot To Bios Get the answer Best answer jscOct 7, 2010, 3:37 AM "Can't get to the BIOS screen" means that it is not POSTing.Work through our standard checklist and troubleshooting thread: mean work

It cannot check the internal parts of the video card. This command will list all disks attached to your computer and assign them a disk number. Report lomax69i› DJ AKSHAY - Jun 1, 2009 at 02:40 PM Hey DJ AKSHAY. check over here I MAY have tried to put in one of the DDR's but they did not fit so it was removed.

When I start my computer up I see the motherboard logo and then it attempts to boot up windows but its no good. The article stated, If the hard drive doesn’t appear in the list at all, it’s possible your hard drive has failed and can no longer be booted from. Hey presto! Vielen Dank.

Do you know what this cold mean? JDFanJan 9, 2010, 9:55 PM Find the clear CMOS jumper and short it with a jumper pin turn the system on and off again and unjump the jumper - that should We spent a lot of time on this. You should have 12 volts while checking with a voltmeter.

Before taking it in to a professional and spending some $$$ I decided to attempt to fix it myself one more time taking your advice with the RAM. It's a fine line and sometimes hard to tell.Note: If your computer won't start and you see a blue screen flash or remain on the screen, you're experiencing a Blue Screen of Melde dich bei YouTube an, damit dein Feedback gezählt wird. what causes it?

wikiHow Contributor Take it to a computer repair specialist in case you are not comfortable doing it yourself. Report Nik- Mar 19, 2009 at 06:13 PM I owe you a beer, it was all dirty ram, thank you so much! Flag as duplicate Thanks! Inhaltsverzeichnis Möglicherweise reagiert Ihr Computer aufgrund einer der folgenden Ursachen nicht: Kein Strom – keine Stromversorgung Kein POST – Einschaltselbsttest kann nicht abgeschlossen werden Kein Start – Das Betriebssystem kann nicht gestartet werden Kein

and having a last check before taking away for service repair. Your Files are Probably OK © Ridofranz / iStock When faced with a computer that won't start most people tend to panic, worried that all the data on their PC is PLEASE help me im at the end of things to try!!!! Take your windows CD and reinstall everything, remember to format the hard disk completely.

Ensure that all your power leads are connected properly. 3 Wait at least 10 seconds. The screen is blank.